Frequently Asked Questions
Everything about IoT SIM cards, from selection and activation to suspension and restoration, covering domestic cards, international cards, the management platform and pricing rules. If your question is not answered here, our 24/7 service line is one call away.
70 questions · 4 topics
IoT SIM Card FAQ
38 questions38 common questions on card selection, activation, IMEI binding, usage controls and troubleshooting.
The Basics
What is an IoT SIM card, and how is it different from a phone SIM?
An IoT SIM card connects machines to the mobile network. It is registered to a company rather than an individual and is used in devices such as trackers, shared bikes, smart meters and in-vehicle navigation. A phone SIM is registered to and used by a person.
Main differences:
- Registration: phone SIMs are registered to individuals, IoT SIMs to enterprises
- Number length: 11 digits for phone numbers, 13 for IoT card numbers
- Capabilities: phone SIMs support calls and SMS; IoT SIMs are data-only in general (voice requires whitelisted numbers, SMS is sent through the platform, and point-to-point messaging is not supported)
- Management: IoT SIMs are managed and queried centrally on an enterprise platform
- Billing: phone SIMs are billed monthly; IoT SIMs are usually prepaid annually, and cards in the same batch can share a data pool
What form factors are available, and how do I choose one?
Four form factors are available — plug-in cards, solder-down (MFF2) cards, eSIM and vSIM — and three durability grades: consumer, industrial and automotive.
- Plug-in card: the same size as a standard SIM (with 3-in-1 punch-outs), suited to devices that need frequent card swaps during testing
- Solder-down card: a chip soldered directly onto the PCB, commonly 2×2 mm or 5×6 mm, suited to volume manufacturing and high-vibration environments such as vehicles and industrial equipment
- eSIM: also soldered in place, but the number can be rewritten remotely, suited to exported devices or devices that change operators frequently
- vSIM: no physical card at all, implemented in software, for special embedded devices
How to choose: use plug-in cards during prototyping; for mass production choose industrial-grade parts in high-temperature scenarios and solder-down cards for devices that move frequently.
Who is UYOU Connection, and which operators' IoT cards can it provide?
UYOU Connection is the first virtual operator in China to hold an IoT resale licence. It is a controlled subsidiary of the listed company Aisidi (SZSE: 002416), listed on the NEEQ (874082), and a pilot enterprise for IoT resale under the Ministry of Industry and Information Technology.
- Domestic IoT cards: available on China Mobile, China Unicom and China Telecom
- International IoT cards: delivered through partnerships with international operators, covering more than 200 countries and regions and over 500 operator networks
What a listed-company structure means for you: transparent finances, annual audits, dependable service and a clear channel for renewals.
What are ICCID, IMSI and MSISDN?
ICCID is the card number, IMSI is the network subscriber identity, and MSISDN is the phone number associated with the card. All three identify an IoT SIM in different contexts.
- ICCID: 19–20 digits printed on the card, beginning with 89. It is the card's identity number and is what you quote when requesting a replacement or suspension
- IMSI: 15 digits stored inside the card and not visible; the network uses it to identify the subscriber
- MSISDN: the externally visible number used when a call or SMS is presented
What is an IMEI, and why are IoT cards bound to it?
The IMEI is the unique identifier of a device. Every cellular module carries a unique 15-digit number — effectively the device's identity card.
Domestic IoT cards use IMEI binding: once activated, a card is tied to the device's IMEI, which prevents it from being pulled out and used in a phone or another device. If you need to move a card to a new device, submit the card number and apply to unbind.
Do IoT cards support 5G? Is 2G still usable?
IoT cards support 5G, but 4G Cat-1 remains the mainstream choice today. 2G base stations have been retired at scale and are shut down across most of the country, so 2G is not recommended for new devices.
- 4G Cat-1: low power and low cost, suited to low-data devices such as shared bikes, POS terminals and trackers
- 4G Cat.4: higher throughput, suited to video surveillance and in-vehicle units that stream video
- 5G: ultra-low latency for autonomous driving, industrial robots and low-altitude economy use cases, at a higher module and data cost
- NB-IoT: ultra-low power but fixed-location only and no voice support; NB coverage has been withdrawn in many areas and pricing is now close to Cat-1, so it is not recommended
Recommendation: for new devices, choose 4G Cat-1 or 5G.
What lifecycle states does an IoT card go through?
The lifecycle runs: purchase → test period → dormant period → in service → suspended → terminated.
- Test period: a trial of up to 3 months with complimentary test data
- Dormant period: stock stage of up to 6 months; no charge while the card is not activated
- In service: normal billing applies
- Suspended: service paused, whether by request, for policy violations, when data runs out or on expiry
- Terminated: the number is cancelled and cannot be restored
What is the test period, and can it be extended?
The test period is a trial of up to 3 months, during which complimentary data is provided so you can verify that the card works with your device.
- If the test data runs out early, the card moves to the dormant period ahead of schedule and must be power-cycled to activate
- If the data is not exhausted, the card moves to the dormant period automatically when the test period ends
- You can also end the test period early and go straight to dormant; the card then activates on first power-up
What is the dormant period, and is it charged?
The dormant period is the stock stage between card production and installation, lasting up to 6 months. No charge applies while the card stays inactive; as soon as it is powered on and connects, it activates automatically and billing begins.
For international cards, a number-retention fee applies once the dormant period exceeds 6 months. An extension can also be purchased at low cost.
How are UYOU cards different from the cheap cards sold on marketplaces?
The difference is who stands behind the card. UYOU Connection holds a formal IoT resale licence issued by the Ministry of Industry and Information Technology and is a controlled subsidiary of Aisidi (002416), so funds flow through regulated channels and after-sales support is backed by the company. Low-cost cards on e-commerce platforms are often fly-by-night offers that can be cut off at any moment with no recourse.
Usage Rules and Controls
Can an IoT card be used in a phone?
No. IoT cards may not be used in phones and cannot reach consumer apps such as WeChat or Taobao.
Operator systems detect the terminal a card is used in and will suspend service immediately if it is found in a phone. The restriction stems from national telecom-fraud prevention regulations.
Can an IoT card make calls or send SMS?
IoT cards are data-only by default: voice is not enabled, and SMS can be exchanged through the management platform but not point-to-point between cards, or between a phone and a card.
- Voice: in specific use cases such as watch trackers or emergency alerts, up to 5 whitelisted numbers can be enabled — UYOU Connection does not currently offer this service
- SMS: can only be delivered from the management platform, for remote device control such as rebooting or changing settings
What is IMEI binding, and what happens when I change devices?
IMEI binding ties an IoT card to the IMEI of a device. Operators now generally apply strict (hard) binding.
- Soft binding: the first device used is bound, and changing devices raises an alert
- Model-level binding: a batch of device models is bound (based on the first 6 digits of the IMEI), so devices within the batch can be swapped
- Hard binding: the card works only in the designated device and is suspended immediately if moved (the current mainstream approach)
To change devices, submit a rebinding request in advance. Once approved the card works in the new device, typically within about 2 working hours.
What is an APN, and how do I configure one?
The APN (Access Point Name) is the entry point a device uses to reach the network. Different APNs map to different network paths and billing policies.
Default APNs of the three Chinese operators:
- China Mobile: cmiot (cmnbiot for NB-IoT cards)
- China Unicom: 3gnet (scuiot for Sichuan Unicom)
- China Telecom: ctnet
How to set it:
- Devices with a screen: enter it manually under Settings → Mobile Network
- Devices without a screen: write it over the serial port with AT commands
- Remote configuration: some cards accept an SMS-based change
Why is my card suspended, and am I still billed?
Common causes of suspension include a voluntary request, a device change that triggers card-device separation, incomplete identity verification, policy violations, exhausted data, hitting a configured data cap, and plan expiry. As long as the plan has not expired, the plan fee is still charged while the card is suspended.
- Suspended on request: can be restored if the plan has not expired
- Suspended for a device change: apply for rebinding; restored once approved
- Identity verification incomplete: complete the verification
- Suspended for a violation (inter-provincial use, fraud-prone areas and similar): restoration can be requested; the card is terminated automatically after the deadline and may not be recoverable
- Suspended because data ran out: purchase a top-up package
- Suspended at a configured data cap: restore manually
- Suspended on plan expiry: renew to restore
What counts as an abnormal suspension?
An abnormal suspension is an automatic block triggered by non-compliant use. There are four common cases: card-device separation (the card is removed and inserted elsewhere), inter-provincial use, use in fraud-prone areas, and use in a phone.
Can an IoT card be used across provinces?
By default cards are restricted to their home province. If you need cross-province use, notify us in advance and apply to lift the regional restriction.
What are blacklists and whitelists for IoT cards?
- Blacklist: listed addresses are blocked, and any attempt to reach one triggers a suspension
- Whitelist: only the listed IPs or domains can be reached; everything else is blocked
Can these controls be removed?
Some controls can be lifted: a device change can be handled by rebinding, and cross-province use by applying for a new region. The traffic-direction restriction on high-data cards and the phone ban cannot be removed.
- Device changed → removable → apply for rebinding
- Cross-province use → removable → apply for a region change
- Traffic-direction restriction on high-data cards → not removable
- Use in a phone → not removable
What is the data cap control, and what happens if I exceed it?
The data cap applies to low-data cards: usage is limited to 300 MB per month. When the cap is reached, data service is switched off automatically and restored the following month.
If you need more, you can move the card to directional (server-specific) data and purchase a top-up package to continue.
How do controls differ between low-data and high-data cards?
The 300 MB monthly threshold separates two sets of default controls.
Low-data cards (≤300 MB per month)
- IMEI binding
- Phone use prohibited
- 300 MB monthly cap (data service is switched off when exceeded and restored the next month)
High-data cards (>300 MB per month)
- IMEI binding
- Phone use prohibited
- Regional restriction (cannot leave the province)
- Access limited to designated servers — directional data, up to 10 addresses per batch
What is directional data, and what are its limits?
Directional data restricts a card to designated IP addresses or domains. It improves security and suits devices that only talk to your own servers, such as a smart meter that connects only to the utility's platform.
- Up to 10 IPs or domains per APN per batch
- Wildcards are supported for domains (for example *.yourcompany.com) but not for IPs
- China Mobile applies stricter rules: the same domain used over different protocols such as HTTP and HTTPS consumes separate slots
- Configuration takes effect in about 3–5 working days
What is a VPDN tunnel?
VPDN is a private tunnel that connects IoT cards directly to your servers, keeping traffic off the public internet.
- Low latency: no detours in between
- More secure: traffic is encrypted, so intercepted data cannot be read
- More stable: unaffected by public-network congestion
It suits security-sensitive deployments such as finance, government services and industrial control.
Do IoT cards have a fixed IP? How can a server reach a card?
IoT cards do not have a fixed public IP. The only way to obtain one is to set up a dedicated VPDN APN and tunnel, where cards under the same APN can be assigned fixed private IPs and reach one another directly.
What data rates can IoT cards achieve?
The theoretical peak is 150–300 Mbps downlink and 50–75 Mbps uplink. Actual throughput depends on the device, the use case, cell signal quality and the surrounding environment.
Do IoT cards need manual activation?
Cards normally activate automatically when the device powers up. If activation does not happen, configure the APN and restart the device; if it still fails, submit the card number to request manual activation.
Troubleshooting
The card cannot get online — how should I troubleshoot?
Work through four steps: hardware → settings → card status → signal.
Step 1: Hardware
- Is the card seated correctly, and is a solder-down card properly soldered?
- Can the device read the card (does it show the ICCID)?
Step 2: Settings
- Is the data switch on?
- Is roaming enabled (required in some scenarios)?
- Is the APN correct?
Step 3: Card status
- Check on the platform whether the card is activated
- Check whether data service is enabled
- Check remaining data and whether the plan has expired
Step 4: Signal
- What is the signal strength at the device?
- Try a different card for comparison
The card suddenly lost connectivity, or registration failed or was rejected — what now?
Domestic cards: confirm on the platform that the card status is normal, refresh it and restart the device; if it still fails, check the APN. Also check whether a core-network control has been triggered — terminals that repeatedly send Attach requests are rejected once the threshold is reached.
International cards: confirm the card status, then check the APN and data roaming settings. If those are correct, check whether the network the card has found is one the number range supports; if not, switch to manual network selection.
The card keeps dropping — disconnecting every few minutes. What can I do?
First decide whether it affects one device or many. For a single device, refresh and reset the card, then power the device down, reseat the card and restart to rule out poor contact. If it recurs, escalate for deeper investigation.
Common causes include use at altitude or in remote areas, weak cell coverage, and an unsuitable heartbeat interval configured on the module.
Module Selection
Which module suits shared-payment devices such as power-bank rentals?
We recommend the ML307C (4G Cat.1). It is low cost, low power and compact (LCC+LGA package), and supports OpenCPU, which removes the need for an external MCU and further reduces bill-of-materials cost.
Is Cat.1 fast enough for video surveillance?
Cat.1 is adequate for occasional snapshots at low resolution (360p/480p). For live HD video (720p/1080p) the uplink is insufficient — move up to a 4G Cat.4 module or the China Mobile MR880A (5G).
Which module suits high-throughput industrial routers and gateways?
We recommend the RG255C or MR880A. Both support 5G/4G across all networks plus 5G LAN and URLLC network slicing, making them suitable for industrial gateways and routers that demand bandwidth and stability.
Any cost-effective 5G module for low-latency applications?
We recommend the China Mobile MR880A. Built on a TD Tech chipset and compliant with 3GPP Release 17, it is cost-optimised while retaining 5G low latency (as low as 20 ms).
My device uses a 2G module — do I need to redesign the board to move to 4G?
It depends on the original footprint. The China Mobile ML307C is broadly compatible: if the board already uses a module from the same vendor, the pins are usually compatible and no redesign is needed. For other vendors, such as SIMCom, pin compatibility must be assessed by the manufacturer.
Do IoT modules include positioning? Can I drop the separate GNSS chip?
Some modules include GNSS, so position data comes straight from the module and a discrete GPS chip can be omitted. The SIMCom A7670X, for example, supports GPS, BeiDou and GLONASS. Confirm against the specific module model.
Do IoT modules support VoLTE voice?
It depends on the model. Some, including the SIM7670X and RG255C, support VoLTE (optional on some variants), so a device can carry voice and data at the same time — useful for senior-care wearables and elevator emergency units.
Do the modules support OpenCPU development?
Yes. The entire ML307C family supports OpenCPU with a complete SDK, so application logic can run directly on the module and substantially reduce peripheral bill-of-materials cost.
For Southeast Asia, should I choose a global or a regional module?
If you only target Southeast Asia, choose the Asia-Pacific variant, which costs less than the global version. We can match the most cost-effective model to each destination country, such as Indonesia or Thailand.
International IoT Card FAQ
10 questions10 common questions on cross-border roaming, APN setup, data security and eSIM deployment.
Using International Cards
How is the APN configured for an international IoT card? Does it change by country?
No. UYOU international IoT cards use a single dedicated APN that works globally, so one configuration covers multiple countries and regions and requires no changes when a device roams across borders.
Contact UYOU technical support for the specific APN parameters.
Is data on an international IoT card secure?
Traffic travels over a dedicated APN channel and an encrypted tunnel, isolated from the public internet, so intercepted data cannot be read. That makes it more secure than buying a local consumer SIM on the spot.
Do international IoT cards support SMS?
Yes. The platform exposes an API for sending SMS commands, and devices can also report SMS back to the platform, which enables remote configuration.
Do international IoT cards support eSIM?
Yes. An eSIM is soldered onto the device, resists vibration and high temperatures, and supports remote SIM provisioning (RSP), so the operator or number can be changed without opening the enclosure. It suits exported devices and fleets spread across several countries.
If devices ship overseas, should servers be hosted locally or abroad?
Host them in the region where the business operates. With international cards abroad and servers in China, the card can show a normal status and consume data while your backend receives nothing; servers in China may also cause some traffic to be blocked.
eSIM
What is eSIM, and do I need to buy a separate chip?
eSIM is an embedded SIM, so no separate plug-in card is needed. It can be implemented by soldering a solder-down (MFF2) card onto the board, or purely in software on modules that support vSIM.
What are the advantages of eSIM over a plug-in card?
The main benefits are industrial-grade resistance to vibration and corrosion, and no need to swap cards on site. If the operator must change — China Unicom to China Mobile, or a local operator after export — RSP handles it over the air, with no visit required.
Which operators can the eSIM platform connect to?
The UYOU eSIM platform is GSMA-certified and connected to major operators worldwide. Any operator that supports the eSIM specifications can have its profiles loaded onto the platform.
How is the number downloaded to an eSIM? Is a QR code needed?
No. IoT devices usually have no screen, so profiles are pushed from the platform: when the device powers up, the platform delivers the profile to the module automatically and the number is provisioned without any manual step.
Can I still use eSIM if my module does not support it?
Yes. For modules without eSIM support, the IPA approach embeds an SDK inside the eSIM card itself, so eSIM service is still available.
IoT SIM Management Platform (Card Manager) FAQ
5 questions5 common questions on platform features, usage alerts, status interpretation and SMS monitoring.
Using the Platform
What can the IoT SIM management platform do?
The IoT SIM management platform (Card Manager) lets an enterprise manage its cards in one place, covering both domestic and international cards.
- Query the status and data usage of every card
- Bulk top-up, suspend or resume service, and change settings
- Configure usage alerts delivered by SMS or email
- View bills and export data
- Open APIs for integrating with your own systems
Will I be warned when data runs low? How do I check usage?
Yes. The platform supports automatic alerts — for example, notify the administrator by SMS or email at 80% usage — so devices are not cut off for lack of balance.
- On the platform: real-time usage
- Alert settings: automatic SMS or email at 80% of the allowance
- WeChat official account: check on a phone at any time
What is the difference between card status and data service status?
Card status shows where the card sits in its lifecycle; data service status shows whether data connectivity is switched on. The two are independent.
A card can read “in service” while data service is off: the card itself is fine but the device cannot get online. Some controls only switch off data service, so check both fields when troubleshooting on the platform.
In SMS monitoring, what is the difference between mobile uplink and mobile downlink?
Mobile uplink is SMS sent from the card to the platform, used for device reporting and emergency alerts. Mobile downlink is SMS sent from the platform to the card, used for remote control such as rebooting or changing the APN.
How downlink messages are sent:
- Single: enter the MSISDN and the message content
- Bulk: download the template, fill it in and upload
Key limits:
- IoT cards cannot message each other
- A phone cannot send directly to an IoT card
- All SMS must pass through the platform; point-to-point messaging is not supported
Can SMS be forwarded automatically?
Yes. Add or import forwarding rules under “card monitoring configuration” in the platform to enable automatic forwarding.
Coverage and Pricing FAQ
17 questions17 common questions on global coverage, operator switching, billing, data pools and renewals.
Coverage
Which countries and regions do international IoT cards cover?
More than 200 countries and regions and over 500 operator networks, drawing on major local operators such as Vodafone, AT&T and SoftBank, and covering both mature markets in Europe and North America and developing regions across Asia, Africa and Latin America.
Can one card work across several European countries?
Yes. A Europe card or a global card roams automatically between countries: no card swap at each border, and billing is unified. It suits use cases such as cross-border logistics tracking.
If signal is poor abroad, can the card switch operators automatically?
Yes. Most international cards support multi-network selection, so a device can switch automatically among local operators — in the UK, for example, from O2 to EE or Vodafone.
For latency-sensitive use cases, can you supply local SIMs?
Local cards are available, assessed case by case. Roaming cards are already very stable; local cards usually lock to a single network and require manual handling for renewals and support, which adds operational complexity.
What if the destination country restricts permanent roaming, as Türkiye and Brazil do?
Türkiye, Brazil and some other countries restrict permanent roaming — an industry-wide constraint. The solution is a local card sourced through local operator partnerships.
How does an international card differ from a local SIM?
- International card: free test data while still in China, access to multiple operator networks abroad, and a unified platform for card status
- Local SIM: usually no testing before shipping, a single network only, higher rates, and no management platform
Can international cards be tested in China first?
Yes. UYOU provides 5 MB of free test data per month, enough to validate the device in a simulated environment in China. Once testing passes, the device connects as soon as it is powered up overseas.
Pricing and Billing
How are IoT cards billed — monthly or annually?
Domestic IoT cards are billed annually. International cards can be billed monthly, with a minimum initial term of 3 months.
How are international IoT cards priced?
Pricing depends on the countries used and the data volume, on a plan basis. Top-up packages cover overage and cross-border settlement is supported. A quotation is provided after assessing the project.
Devices shipped abroad but never activated — will I be charged?
No. A 6-month dormant period can be set from the moment cards are shipped; no activation means no charge. If 6 months is not enough, an extension is available at low cost.
What is a data pool, and how does it differ from per-card data?
Per-card data belongs to each card alone: only the card that overruns is suspended. A data pool shares one total allowance across several cards — 10 cards sharing 10 GB, for example — and stays live as long as the total is not exceeded.
- Many devices with uneven usage → choose a data pool; it costs less
- Few devices with predictable usage → per-card data is simpler
Note: cards must share the same operator, plan and fee to be pooled. Once the pool total is exhausted, every card in the pool is suspended for the cycle and restored automatically in the next one. Pools built on general low-data plans of 300 MB or less carry a cap: each card is limited to 300 MB per month before data service is switched off, restored at the start of the following month.
Will I be overcharged if data runs out?
No. Once data runs out the card is suspended and cannot go online, but no arrears accrue. A top-up package can bridge the gap, and service resumes automatically the following month.
We recommend enabling usage alerts at 80% to avoid an unexpected suspension.
Can a plan be upgraded or downgraded?
Upgrades (1 GB to 2 GB, for example) are generally possible on payment of the difference. Downgrades depend on the contract and are not permitted in some. Changes are usually requested before expiry and take effect the following month.
What is number retention, and how is it charged?
Number retention pauses service while keeping the number, so it can be restored later.
- Takes effect the day it is requested; the full month's plan fee is still charged regardless of the date
- From the next month a retention fee applies, lower than the plan fee
- The plan's validity continues to run and is not extended
Will I be reminded before the plan expires? How do I renew?
Yes, between 60 and 30 days before expiry.
- Top up online on the management platform
- Renew through the WeChat official account
- Renew by corporate bank transfer
Can devices be blocked from high-bandwidth apps such as TikTok or YouTube?
Technically a directional data policy can block them, but it is usually not advisable: overseas data is priced high and a block-only approach rarely covers the cost. The more common practice is to restrict the device to your own server addresses.
Does eSIM cost more than a standard solder-down card?
Hardware costs roughly double those of a conventional solder-down card, plus provisioning and connectivity fees. It suits scenarios that change countries frequently or involve high-value devices; for low-value devices it is not recommended.
Did not find your answer?
Our 24/7 service line and technical support handle selection, provisioning and troubleshooting directly.